You will also find a variety of colors, as well as tumbled and beveled bricks, that offer different styles. Concrete pavers, though not the same thing as brick, come in similar shapes and sizes and are installed in much the same way, so you may wish to consider them.
Tips for Planning a Brick Path or Patio
Many people make brick patios too small because they underestimate how much space they’ll need for furniture. To avoid this mistake, take the furniture you plan to put on your new patio and place it where you think you’ll want it to be. Walk around the furniture and use it like you normally would. When you feel comfortable with the arrangement, gauge how large the space needs to be. Then use spray paint to mark the perimeter of the patio. Brick paths should be at least 3 feet wide, but you’ll appreciate a 4-foot-wide path a lot more. Use the path to connect entrances (to your home and garage, for instance) and different areas of the yard. A brick path can unify spaces outdoors the same way flooring does indoors.
Tips for Installing Brick Paths and Patios
Installing brick patios or pathways is one of the more laborious outdoor projects you can attempt, and it’s important to approach it realistically. Many homeowners see a patio or path as a weekend project. Often that’s overly optimistic. If it’s your goal to lay a brick walkway or patio in a weekend, you need to have all the planning done beforehand and do all you can to reduce labor. Rent a tiller to loosen soil so it’s easier to excavate, use a vibratory compactor rather than a hand tamper, and have a masonry saw on hand for easy brick cutting. When you have material delivered, have it placed as close to the work site as possible. And if you can recruit help, do so. The key to a long-lasting brick surface is laying a proper base. Scraping off lawn and then laying brick over a couple inches of sand is a sure way to create an uneven, unstable surface. A good installation consists of 4 to 6 inches of base rocks and 1 inch of sand topped by bricks. That’s about 8 to 10 inches total that you need to excavate below the level you want the finished brick path or patio to be. You also need to excavate several inches beyond where the edges will be. Try to avoid digging too deep and having to backfill; this can create pockets of soft soil that can settle, leading to dips in the paving. If you do have to backfill spots, compact them before laying base.
What You Need
Base of soil and gravelSandCompactor, hand or vibratoryRakeLandscape fabric (optional)Plastic edgingStakes1-inch PVC pipeStraight boardBricksMalletChisel and hammer, or masonry saw
Step 1: Spread the Base
Spread the paver base evenly and pack it thoroughly with a compactor. A hand tamper is adequate for small areas, but for large areas, a vibratory compactor means far less work. It’s best to apply half the base, compact it, then apply the rest and compact it again. To achieve a smooth final surface, use a rake to fill in low spots with more base or shave off high spots, and continue to compact the base until the entire area is smooth and even. Laying landscape fabric over the compacted base before adding sand gives the installation more stability.
Step 2: Add Edging
Use plastic edging to define the perimeter of your paving area, whether it’s straight edges or curves. Hold it in place with stakes.
Step 3: Level the Sand
Where you want to begin laying brick, set two lengths of 1-inch PVC pipe a couple of feet apart. Then add about 1 inch of sand over this area. Slide a straight board across the pipes to create a smooth bed of sand 1 inch thick. Do not compact it.
Step 4: Lay Your Brick
Place bricks one at a time in the desired pattern. As you work, use a level to spot bricks that are slightly higher than surrounding bricks. Tap them with a mallet to set them lower into the sand. If a brick sets slightly lower, remove it, add a bit of sand, and replace it. Continue placing bricks in this fashion, saving the edge pieces for last.
Step 5: Add Finishing Touches
You can use a chisel and hammer to cut brick, but it’s far easier to use a masonry saw. Rent one at a tool rental outlet. Measure each brick piece individually, make the cut, and place the brick with the cut end on the outer edge. Then spread a light layer of sand over the paving. If you still have the compactor, use it on top of the brick (with the light layer of sand still present). Sweep the sand around so it fills the small gaps between bricks.
Bonus: Choosing Brick Patterns
You can use any of several patterns when you lay brick. Classic patterns include basket weave, running bond, stack bond, and herringbone. Your choice is largely a matter of personal preference, though the patterns that can give you a straight edge without cutting (basket weave and stack bond) might require a bit less work depending on the shape of the area you wish to pave.
